How to paint a ceiling with a sprayer

This article was co-authored by Archie Guerrero. Archie Guerrero is a Commercial and Residential Painting Specialist and the Operations Manager for DGP Painting in Austin, Texas. With a decade of experience, Archie specializes in interior and exterior painting and staining, cabinet refinishing, and wallpaper and popcorn removal. DGP Painting offers clients environmentally friendly paint materials and top-of-the-line paint products. DGP Painting has an A+ rating with the BBB and has been in Austin’s “Best of the Best.”

There are 11 references cited in this article, which can be found at the bottom of the page.

This article has been viewed 4,544 times.

Using a sprayer is a fast and efficient way to paint. They’re popular with professionals who have to cover a lot of ground in a short amount of time, so a sprayer may be the best choice if you want to get a job done fast. Painting a ceiling with a sprayer isn’t much different from painting walls. You still have to prep the area, clean out the sprayer, and work in broad, even strokes. With the right prep work and technique, you should finish painting your ceiling in no time!

How to paint a ceiling with a sprayer

How to paint a ceiling with a sprayer

Archie Guerrero
Commercial & Residential Painting Specialist Expert Interview. 17 June 2021. Use a plastic sheet instead of cloth so paint spills won’t soak through. [2] X Research source

  • Try to remove as much furniture as you can before starting. This way, you won’t have to work around any obstructions while you’re painting.

How to paint a ceiling with a sprayer

How to paint a ceiling with a sprayer

Archie Guerrero
Commercial & Residential Painting Specialist Expert Interview. 17 June 2021. Line each sheet up with the top edge where the wall meets the ceiling and tape it in place. Work around the whole room until all the walls are covered. [4] X Research source

  • Cut holes in the plastic around any windows so you can ventilate the room.
  • Use plastic instead of cloth sheets. The paint can soak through cloth.
  • If you’re also planning on painting the walls, then you don’t have to worry so much about covering them. You can paint over any splashes or imperfections when you re-paint the walls.

How to paint a ceiling with a sprayer

How to paint a ceiling with a sprayer

How to paint a ceiling with a sprayer

Archie Guerrero
Commercial & Residential Painting Specialist Expert Interview. 17 June 2021. Attach 120-grit sandpaper to a pole sander. Then apply moderate pressure and sweep the sander across the ceiling. Continue sanding until you cover the whole ceiling. [7] X Research source

  • You’ll probably have to change the paper a few times. When it feels like the sander isn’t gripping the ceiling as well, then the paper is clogged and needs changing.
  • If you don’t have a pole sander, you could use regular sandpaper while standing on a latter. Be very careful and maintain your balance and don’t stand on the highest step.

How to paint a ceiling with a sprayer

Related Articles

  • How to Paint Cabinets With an HVLP Sprayer
  • How to Easily Paint a Ceiling
  • How to Paint a Stomped Ceiling With a Sprayer
  • How to Paint a Refrigerator
  • How to Create a Textured Ceiling With Paint and Drywall Mud

Electric sprayers are all airless, which means they have a hydraulic pump to force paint through the spray tip. This results in a large volume of paint and, if you use a wide tip, significant overspray. Professional painters usually have a gun that connects to the pump via a high-pressure hose, but if you’re only an occasional painter, you can get good results with less bother by using a cup-style gun.

Choosing the Sprayer and Tip

Most hardware stores sell handheld electric, cup-style spray guns, but you have to work from a ladder when using one of these unless the ceiling is unusually low, and you’ll be refilling the cup frequently. A better option is to rent a small airless sprayer from a rental outlet that has a wand-style gun. The tip regulates spray volume and width. You can usually use the tip that comes with a cup-style gun, but you’ll have to choose the right one for a larger machine. Make sure the aperture is wide enough for the paint you’re using — but not too wide — and the spray width isn’t too narrow, or you’ll have drips.

Preparing the Ceiling

Before you use an airless sprayer, it’s vitally important to cover everything you don’t want painted. Unlike that from a can of spray paint, the overspray from an airless sprayer is wet when it settles. If you can’t take the furniture out of the room, cover every part of it with plastic. If you’re only painting the ceiling, you should also cover the walls with plastic, using painter’s grade masking tape to make a clean line between the wall and the ceiling. You can always cover the ceiling fixtures with masking paper, but it’s much cleaner to turn off the power to all the ceiling light fixtures, take them down and tape around the boxes.

Painting Procedure

While spraying a large surface with an airless sprayer, you should hold the tip about 6 to 12 inches away. It’s best if you can spray in full sweeps from one wall to the other, but if you’re on a ladder or the ceiling is very large or irregular, you’ll have to work in sections. Try to feather the spray at the point where sections overlap by gradually moving the tip away to avoid uneven coloring. Before spraying, you should test the pattern on a piece of cardboard and eliminate uneven paint distribution by adjusting the pressure setting or the gun controls.

You usually don’t have to thin paint before spraying it through an airless sprayer, but you should if you notice low spray volume or chunks of paint material. Avoid thinning more than 20 percent, or you may have drips. It’s just as important to cover your body as it is to cover furniture, and that includes your face and hair. Many professionals wear ski masks, goggles and a respirator. Even latex primer will gum your equipment if you don’t clean up properly at the end of each day. Spray solvent through the machine until it runs clear, and then leave the solvent in the cup or hose until you need the machine again.

The quickest way to paint a ceiling is to spray paint it. It’s much quicker than using a roller and definitely faster than using a paintbrush. However, it is something that needs plenty of preparation and knowledge of how to use the paint sprayer in order to achieve good results.

Step 1 – Pick a Type of Sprayer

There are three types of paint sprayer that can be used to spray paint the ceiling. These are the airless spray, the compressed air spray, and the electric pump. To spray paint the ceiling, use an airless paint sprayer. It’s the most efficient way to spray paint a ceiling.

Unless you’re going to be painting very regularly, rent the airless paint sprayer and get advice on how to use it, such as the best nozzles to use. Also learn how to clean it. Be fully familiar with the unit before you start to paint. Doing so will make you more confident and your spraying will be much better.

Step 2 – Prepare

If you’re using any appliances in the vicinity of the painting, turn them off. Paint could damage them or even cause an explosion if they’re left on. Move all the furniture out of the room. Put drop clothes all over the floor to protect them. To keep the paint off the walls, hang drop cloths from the top of each wall, covering every inch. Attach them with masking tape. Openings in and out of the room should be covered with plastic, although this should be unsecured at the bottom to allow you to enter and exit.

Step 3 – Paint

WARNING: Before you begin to spray paint the ceiling, put on safety goggles and wear a mask. There will be plenty of minute paint droplets in the air and you don’t want to inhale them. It’s also advisable to cover your hair and wear a long-sleeved shirt.

Pour the paint through a paint strainer into the bucket of the airless paint sprayer. The sprayer is vital to keep out small foreign objects that could clog the paint sprayer. The paint will need to be thinned. Follow the instructions from the paint manufacturer and don’t thin more than instructed.

Step 4 – Spray

Set the sprayer correctly. One of the advantages of a sprayer is that you don’t need to be on a ladder to spray paint the ceiling. Set the paint sprayer to give full, light coverage. Work from the center of the ceiling out towards the edges and corners.

You only want to spray a light coat on the ceiling. Spray in even strokes to achieve this. It’s much better to put on two light coats of paint rather than a single thick one. Allow the paint to dry fully between coats. Clean the spray painter nozzle after each coat of paint to ensure the best coverage.

How to paint a ceiling with a sprayer

Related Articles

  • Textured Drywall Techniques and Swirls
  • How to Paint Glow-in-the-Dark Stars on a Ceiling
  • Ceiling Finishing Techniques
  • How to Splatter Drywall
  • How to Paint Over a Sponged Wall

Stomped ceilings offer texture and visual interest without the tacky assertiveness of popcorn ceilings, but they can be a challenge to deal with if you are redecorating. Scraping away the texture or covering it with a dropped ceiling can be messy, time consuming and expensive, but those are not your only options. Painting a stomped ceiling is not difficult if you use a sprayer.

Stomped Ceilings

The term ‘stomped ceiling” refers to a particular method of creating a textured surface. This is achieved by rolling drywall compound that has been thinned slightly with water onto the ceiling. The wet drywall compound is then “stomped” by means of a fat brush not unlike the very fat brushes that women use to apply face or body powder. Turning the brush between stomps varies the pattern. When applied by professionals, a stomped ceiling is often created by two people working at once. The first person rolls the drywall compound onto the ceiling while the second does the actual stomping.

Preparation

Practice on an exterior wall or other flat surface with clear water in the sprayer before attempting to spray with paint if you have never used a sprayer before. Place drop cloths over any furniture that will not be removed from the room. Cover the floor with a cloth tarpaulin because they are less slippery than plastic drop cloths. Tape off the tops of your walls with brown craft paper or newspaper and painter’s tape to protect them from splatters.

Priming

Primers act as a thin layer of adhesive between the surface of the ceiling and the paint. Oil-based, alkyd or epoxy primers give the best adhesion, but they are not all compatible with every kind of paint. But ceilings do not get the same kind of wear and tear from repeated washing that walls do, so whether or not you use a primer is purely a matter of personal choice. If you choose to use a primer, spray the edges of the ceiling first and then fill in the center.

Painting

Choose a paint that is compatible with your primer. Start with the sprayer at the slightest pressure and increase it slowly until your spray pattern has defined edges. Use a slow and gentle back and forth motion and keep the sprayer nozzle the same distance from the ceiling at all times. Wear a painter’s mask and safety goggles to avoid breathing in the fine mist from the sprayer or getting paint droplets in your eyes.

  • Utah State University Cooperative Extension: Selecting Paint
  • Behr Process Corporation: How to Paint a Home Ceiling
  • Magnum Graco: How to Use a Paint Sprayer – Paint Techniques

Emmy-award nominated screenwriter Brynne Chandler is a single mother of three who divides her time between professional research and varied cooking, fitness and home & gardening enterprises. A running enthusiast who regularly participates in San Francisco’s Bay to Breakers run, Chandler works as an independent caterer, preparing healthy, nutritious meals for Phoenix area residents.

Painting without hitting the ceiling is not an easy task. Without a small amount of doubt, I can say this is the most annoying thing at the time of painting walls. Especially when we paint the walls near the ceiling, it is about to happen very quickly. It’s really irritating and embarrassing to see our ceiling hit or greased or being spoiled by our wall paint, especially if it’s a newly painted one. But it is avoidable. Painting walls seem to be easy, but it is not that easy. But don’t worry, you can still paint your walls and decently decorate your room. Today, we will discuss how to spray walls without hitting the ceiling.

Table of Contents

​Step One: Protecting the Room

Dry the walls: you can use a clean cloth or any kind of element that has the power of absorbing. Make sure there left no moisture on the wall. Wait until it is properly dried.

​​Step Two: Spraying the Wall

Frequently Asked Questions

Can I Spray Paint in Public?

Unless you have a permit, this is not a good idea, since there are laws against it.

If, however, you are hired by a cafe to decorate their terrace, for example, you can do it, of course.

Please do not touch historic buildings, please. In my country, many historic buildings are being vandalized with spray paint; this is an incredibly disappointing sight to see during a walk through the city. Mutilated buildings kill the unique charm of each city.

If you enjoy spray painting, please do it in legal areas or for hire, because if you don’t, the law will not be on your side. Anything damaging public and private property will get you in serious trouble.

Where Should I Paint First? Ceilings or Walls?

We suggest you spray the ceiling first definitely. Can easily roll all around the perimeter as well, spraying is comparatively easy in the corners and watch for drips. Apply gentle pressure with the sprayer force in order to fill the seam between walls and ceiling.

If your ceiling could use a touch-up, you may be wondering about the best way to paint a ceiling. Painting is relatively easy when compared to other home upgrades but there are many things to consider before you begin. You’ll need to choose the right interior paint and tools and pick your colors appropriately.

In this post, we’ll give you some pointers on how to paint a ceiling like a pro. If you opt not to do the job yourself, you’ll know enough to ensure your painter is doing the right thing. After you learn the best way to paint a ceiling, contact Alpine Paint to get the products and tools you need. Alpine Paint is a paint store created by painters and we offer an extensive range of paints, sprayers and other supplies.

How Do I Decide What Color to Paint My Ceiling?

If you’re wondering about what color to paint your ceiling, the answer depends on the look you want to achieve. The color of your ceiling will affect the lighting and overall ambiance and feel of the room. Ceiling paint can be used to brighten up a room or add warmth and character. While white is the traditional option, there are many other choices. Here are some tips and tricks that may give you some ideas:

  • Paint your ceiling the same color as your walls. If your walls are light blue, grey or beige, this will work well. It eliminates the stark contrast between your walls and ceiling and makes the other colors in the room pop. if you want your furniture, artwork or drapes to stand out, this is an excellent idea.
  • Paint your ceiling a few shades lighter/darker than your walls. This also creates a cohesive look but it adds a little more interest. If the room has very tall walls, paint a ceiling in a darker color to make the room seem cozier. If the ceilings are low, painting them a lighter color than the walls will make the room seem bigger and airier.
  • Paint your ceiling a completely different color. If you’re still not sure what color to paint your ceiling, this may be the best option for you. When you have neutral walls, a contrasting ceiling can make your room look a lot more interesting. Many homeowners like black and grey but you’re only limited by your imagination. Using a color which is in your in our accents or decor will work well.

No matter what you decide in the end, you’ll find ceiling paint from numerous paint brands at Alpine Paints. You can even create a sand paint ceiling if you want to add texture as well as color.

How to paint a ceiling with a sprayer

How to Paint a Ceiling With a Roller and Get the Best Results

Once you’ve chosen the perfect paint to refresh your ceiling, you need to think about how you will apply that paint. If you choose a roller, you need to know how to paint a ceiling with a roller to get professional results. Painting a ceiling with a roller isn’t difficult but you need to be careful to avoid roller marks. One way to do this is to use flat latex paint instead of eggshell or semi-gloss finishes.

First, you need to use a brush to apply the paint around the edges. Then, start at a corner of the room and roll a 4 to 5-foot section starting a few inches away from the brushed portion and using a zig-zag pattern. Go over the same area again to fill in the spaces and blend in the brushed edges. Roll back and forth to smooth the coat. Start a second swath a few inches away and use the same technique before blending the two swaths. Continue doing this until the ceiling is finished.

You now know how to paint a ceiling with a roller, but if this seems like too much work, try the following technique.

How to paint a ceiling with a sprayer

How to Spray Paint a Ceiling Flawlessly

Spray painting is the quickest way to get the job done but you still need to know how to spray paint a ceiling to get beautiful results. You’ll need to use an airless paint sprayer and ceiling spray paint. Before you begin to paint, put on goggles and a safety mask and use a strainer to get the paint into the sprayer.

When you’ve done that, set the sprayer to deliver light coverage. Start in the center of the ceiling and work towards the corners and edges. Spray in even strokes and allow the first coat to fully dry before applying the second one.

If you’ll only be using the spray for this project, it is better to rent the equipment than buy it. We offer a convenient paint equipment rental service at Alpine Paints, and we’ll give you tips on how to spray paint a ceiling using our equipment.

How to paint a ceiling with a sprayer

Should You Paint the Ceiling or Walls First?

After you choose a color and learn some basic painting methods, you need to clarify another important detail when you paint a ceiling: should you paint the ceiling or walls first? You may be more excited about painting your walls but you should do the ceiling first since the paint is likely to splatter or spray and get all over your walls. Do the ceiling, tape it off when it’s dry, and move on to the walls.
If you are interested in painting your ceiling and making your home more beautiful and comfortable, do not forget about choosing quality materials, top-of-the-line paint brands, and excellent tools. Choose Alpine Paint for all your needs.

How to paint a ceiling with a sprayer

How to paint a ceiling with a sprayer

The Spruce / Margot Cavin

  • Working Time: 1 hr
  • Total Time: 4 hrs
  • Skill Level: Beginner
  • Estimated Cost: $40 to $65 (per 200-square-feet of ceiling area)

If you are reluctant to take on the potentially awkward job of painting your ceiling, you are not alone. But there are ways to paint over your head that are less strenuous, help you eliminate most drips, and lets you judge whether you are covering the entire ceiling.

On the bright side, in many cases, you are painting the ceiling white again (with the only caveat is that not all white paints are the same shade). Most same-color painting jobs are far simpler than laying on a new color coat. Painting over your head is made easier when you use the right size nap roller cover and the right length of an extension pole. Once you get the room entirely prepared, you will find that the job of painting your ceiling goes quickly and with only minimum effort.

Basic Tips for Painting the Ceiling

Ceiling paint is formulated differently than wall paint—its thicker and stickier formulation is meant to eliminate most drips, and best used with a roller cover with a 3/8-inch nap if painting a smooth ceiling and a thicker nap for textured ceilings. Flat or matte white ceiling paint is the most popular type of paint for a few significant reasons:

  • Flat and matte paint hides imperfections on the ceiling more than satin or glossy finishes that highlight every flaw on the surface.
  • The white bounces and reflects more light in the room resulting in a brighter space.
  • White ceiling paint provides a limitless vista for your eyes that gives the illusion that the room is larger than it is, whereas a colored ceiling offers the illusion of a smaller space.

Finally, don’t worry if you paint your ceiling before or after your walls—either way is fine. Regardless of which order you paint a room, you will inevitably drip or splatter a little bit of ceiling paint on the walls or wall paint on the ceiling that will need touching up. However, if your walls are completely dry, it may be easier to protect every inch of them by running plastic sheeting around the room using painter’s tape, as in the photo above, then painting your ceiling.

Ceiling painting is strenuous, drip-prone, and hard to judge if you are getting all of it covered. Most painters, professional, amateur, and otherwise, dislike painting ceilings.

here is how to make your ceiling painting project go as smoothly as possible:

step 1 : choosing the airless sprayer and tip

Most hardware stores sell handheld electric airless sprayers or cup-style spray guns, but you have to work from a ladder when using one of these unless the ceiling is unusually low, and you’ll be refilling the cup frequently. A better option is to rent a small airless sprayer from a rental outlet or purchase a small airless sprayer DIY type like DP-X6. The tip regulates spray volume and width. Make sure the aperture is wide enough for the paint you’re using — but not too wide — and the spray width isn’t too narrow, or you’ll have drips. Our standard tip size for DP-X6 is 517 10″-12″ fan width.

Step 2: preparing the ceiling

Before you use an airless sprayer, it’s vitally important to cover everything you don’t want painted. Unlike that from a can of spray paint, the overspray from an airless sprayer is wet when it settles. If you can’t take the furniture out of the room, cover every part of it with plastic. If you’re only painting the ceiling, you should also cover the walls with plastic, using painter’s grade masking tape to make a clean line between the wall and the ceiling. You can always cover the ceiling fixtures with masking paper, but it’s much cleaner to turn off the power to all the ceiling light fixtures, take them down and tape around the boxes.

Step 3: Painting

While spraying a large surface with an airless sprayer, you should hold the tip about 6 to 12 inches away. It’s best if you can spray in full sweeps from one wall to the other, but if you’re on a ladder or the ceiling is very large or irregular, you’ll have to work in sections. Try to feather the spray at the point where sections overlap by gradually moving the tip away to avoid uneven coloring. Before spraying, you should test the pattern on a piece of cardboard and eliminate uneven paint distribution by adjusting the pressure setting or the gun controls.

You usually don’t have to thin paint before spraying it through an airless sprayer, but you should if you notice low spray volume or chunks of paint material. Avoid thinning more than 20 percent, or you may have drips. It’s just as important to cover your body as it is to cover furniture, and that includes your face and hair. Many professional painters wear ski masks, goggles and a respirator. Even latex primer will gum/block your equipment if you don’t clean up properly at the end of each day. Spray solvent/water through the machine until it runs clear, and spray gun / tip / safety guard / gun filters etc. need to clean with a softer brushHow to paint a ceiling with a sprayer.

How to paint a ceiling with a sprayer

How to paint a ceiling with a sprayer

Kelly Bacon is a licensed general contractor with over 40 years of experience in construction, home building and remodeling, and commercial building. He is a member of The Spruce Home Improvement Review Board.

How to paint a ceiling with a sprayer

eyecrave / Getty Images

  • Working Time: 2 – 4 hrs
  • Total Time: 1 – 2 days
  • Yield: 500 square feet of ceiling
  • Skill Level: Beginner
  • Estimated Cost: $100 to $150

After enough time, popcorn ceilings begin to look dull, weary, and dated. Removing the popcorn texture coating is messy, but painting the popcorn ceiling is one way to bring back the ceiling’s sparkle and freshness for little cost and with minimal mess.

Type and Quantity of Paint to Use

Interior acrylic-latex paint is the best type of paint to use for popcorn ceilings. Flat or matte is the traditional sheen for ceilings, since it reduces light bounce. If you need to protect your ceiling from moisture, though, use eggshell, satin, or semi-gloss paint sheens.

Popcorn texture ceilings require more paint than flat ceilings. One gallon of ceiling paint covers between 400 to 500 square feet of flat ceiling; double the quantity of paint for popcorn ceilings.

Paint, Cover, or Remove Popcorn Ceiling

Painting a popcorn ceiling is just one way to improve its appearance. For the long-term, it’s helpful to weigh painting the ceiling against covering the ceiling or removing the popcorn texture.

Paint Popcorn Ceiling

Painting a popcorn ceiling is faster and easier than covering or removing the texture. It’s less expensive than covering the ceiling, too.

Encapsulates potential asbestos

Textured appearance remains in place

Possibility of asbestos if you need to disturb the surface

Cover Popcorn Ceiling

Popcorn ceilings can be covered with 1/4-inch or 1/2-inch drywall or with tongue-and-groove wood planks installed directly over the popcorn texture. The covering is screwed into the joists above the ceiling.

Creates flat ceiling

Covers any potential asbestos

Creates ceiling thickness

Adds weight to ceiling

Most expensive option

Remove Popcorn Ceiling

Popcorn ceilings can be removed with warm water, a scraper, and plenty of patience. While it’s messy, it’s the ultimate way to return your ceiling to a flat state.

Creates flat ceiling

No height or thickness issues

Eliminates any asbestos

Potential asbestos risk

Possible lead paint hazard

Safety Considerations

Some popcorn ceilings may contain asbestos. Prior to 1978, when federal law banned its use, asbestos was added to ceiling texture for its resistance to heat. Plus, the asbestos fibers helped strengthen the material. Through research, asbestos has been proven to cause lung cancer, mesothelioma, and asbestosis. Popcorn ceilings in older homes may contain asbestos.

Asbestos does not always have to be removed. As long as the asbestos remains undisturbed, it can remain in place and be covered with paint or with drywall. If the asbestos-containing material is cut, broken, drilled, sawn, or sanded, asbestos fibers may be released into the air. Call qualified asbestos mitigation specialists if you need to do this.

We all know that we should spray paint the ceiling first and then the wall to get the best results. However, after painting the ceiling, some people will feel awkward when starting the next step. So, how do you spray paint a wall without hitting the ceiling? Let’s find out the answer with Handtoolshouse in the article below!

How do you spray paint a wall without hitting the ceiling?

  • Step 1: Cover all the furniture (the ceiling particularly) and prepare your room.
  • Step 2: Prepare the wall.
  • Step 3: Protect yourself.
  • Step 4: Spray the wall and leave it dry.
  • Step 5: Clean up the room.

How to paint a ceiling with a sprayer

Prepare for the wall spraying is important

Related:

  • Best Airless Paint Sprayer – Reviews in 2021
  • Step 1: Cover all the furniture and prepare your room

    • Take away all the furniture: Get rid of everything that might get in your way. The staff which is hanging on the wall, the mirror, or any type of things to be hung must leave outside of the room. Window curtains and other decorations in the room should be kept out of the room. If there is any bulky furniture, grab it in the corner of the room and cover it with a sheet or thin cloth. If there’s anything on the ground, it might not be in your way now, but maybe in the future, consider taking those things out of the paint room.
    • Turn off mains power: Before starting painting operations, turn off all power lines. You can do it using your home circuit box. Do not touch electrical parts such as lights or meters unless you are one hundred percent sure that it is safe. If you are sure, remove them from the wall. Be cautious, if you can’t remove any of them, ask a technician. Some of these may require a screwdriver to remove.
    • Cover the entire floor: You can use a plastic tarp or absorbent cloth. While it’s not possible to paint the entire wall at once, it’s a good idea to cover the entire floor at first because the risk of crying remains. After securing the floor with tarpaulin or cloth, let heavy personnel run through it as if it were immovable. You can have everything in your house, or you can find it at the hardware store nearby.
    • Cover the ceiling closer to the wall: You can use painter’s tape to cover the ceiling. It is the most suitable as it does not leave anything sticky on the wall. Use as much tape as you need. But most of the time, it doesn’t have to be longer than two to three feet. Don’t forget to wear a mask and open a nearby window. You don’t have to wear gloves, but it can help. Remember, ventilation is vital to the painting.

    Step 2: Prepare the wall

    • Wash the wall with warm water: Scrub the wall with a sponge. Try to delete old strains, if any. You can use detergent with warm water. It needs a specific device to spray paint the interior.
    • Dry the wall: You can use a clean towel or any material that can absorb moisture. Make sure not to leave moisture on the wall. Wait until it is properly dried.

    How to paint a ceiling with a sprayer

    Always remember to protect yourself before paint spraying

    Step 3: Protect yourself

    • Protect yourself: You will need protection to work with spray paint. This is not optional; It is mandatory because spray paint fumes are toxic and can cause serious health problems. You need to protect your eyes, and you also need to protect your nose and mouth. You should also wear clothing that is thick enough that it won’t stick to your skin and gloves. This is a serious thing. I have had health problems that are not directly caused by spray paint but are definitely aggravated by it. Proceed with extreme caution, and if possible, avoid it at all costs. You can always paint acrylic on (almost) any surface imaginable. Wall included. But don’t endorse it unless it’s a coffee shop or your room.

    Step 4: Spray the wall and leave it dry

    • Pour the paint into the bowl: If you’re not comfortable enough with the bowl, use a bucket with a suitable handle. You can mix a little water if needed. Latex paint can always be used.
    • Start from the corner: Place your sprayer against the wall in the corner. You can use a ladder if it must reach the ceiling. Place your sprayer on the right spot and start spraying. Make sure you do not touch the ceiling while spraying. Give it a soft finish, so the primer sprayer lays flat on the wall. But again, you are unlikely to touch the ceiling. Allow enough time to make sure the sprayer is evenly distributed over the wall without splashing onto the ceiling.
    • Let the paint dry: Now that you’ve finished spraying the wall, let it dry for a while. After making sure everything is dry, it’s time to remove the tape covering the corner of the ceiling. Notice how you have a perfectly straight line between the ceiling and the wall.

    How to paint a ceiling with a sprayer

    Don’t forget to clean up the room after paint spraying

    Step 5: Clean up the room

    • Clean your workspace: Your walls are now beautifully painted and all that remains is to clear your workspace. Remove all tarps/newspapers from floors and window corners. Store the remaining spray paint in your inventory. Finally, remove your safety gear and you’re done.
    • Pro tip: If you feel a little dizzy or short of breath, remember to stop everything immediately. Get out of your workspace, remove your mask, and rest for a while. Remember, your health is your first priority.

    Final Thoughts

    To answer the question: “ How do you spray paint a wall without hitting the ceiling? ”. We think it’s best to be well prepared. The key is to move all the furniture out of the room and then use special tape to cover the parts of the ceiling closest to the wall. If you have any other questions related to paint sprayers, do not hesitate to contact Paint Sprayers!

    How to paint a ceiling with a sprayer

    Before Hiring a Painter, Ask These 7 Questions

    How to paint a ceiling with a sprayer

    When Repainting Your Kitchen Cabinets, Avoid these five Mistakes

    How to paint a ceiling with a sprayer

    If painting your ceiling sounds intimidating, you’re not alone. Quite frankly, most painters, amateur, professional, and otherwise, are not necessarily fond of this somewhat messy and uniquely awkward job. Generally, painting over your head can be extremely strenuous.

    Now, covering your ceiling with paint is one thing and professionally painting your ceiling without getting paint on your wall or splattering is another thing. It’s even more difficult if you’re only painting your ceiling and not the walls, because splatters and drips on the wall might easily mean having to repaint your walls as well.

    In this article today, we will share quick tips on how you can successfully paint your ceiling without paint drips and splatters getting on the walls.
    Here we go:

    Buy Special Ceiling Paint

    There’re paints specifically formulated for painting ceilings, and you will generally get the best results with these kinds of products. When painting the ceiling, you want paint that doesn’t splatter and dries slowly. Additionally, instead of glossy finishes, consider a flat or matte sheen. Flat sheens are great at hiding minor imperfections and do not have an overbearing shine.

    The choice of paint color will entirely depend on your preferences. But you probably won’t go wrong with the classic white because it’s considered a “safe” choice for most spaces.

    Stick with a Roller

    Sure, you can paint your ceiling faster using a paint sprayer, but by the time you will have the entire ceiling fully painted, pretty much everything else will be covered in paint –this includes you, the walls and every other item in the room. Painting a ceiling with a roller will give you the best coverage without splatters and will also save you from straining. Of course, you will need a paint brush every now and then –like when cutting in and covering tight spaces.

    Remove Everything from the Room

    As you can imagine, painting the ceiling can be quite a messy job. Remove everything that can be removed from the room –this includes wall hangings, furniture, decorations, appliances, the carpet, and so on. Anything that cannot be removed such as the inbuilt cabinets and appliances should be fully covered using drop cloths to prevent paint from dripping on them.

    Don’t Ignore the Painters’ Tape

    While some professionals can successfully paint a straight line between the ceiling and the walls without a painter’s tape, it’s usually a calculated risk and you can always tell the difference. If you really want that straight light at the edge of your ceiling, consider using a painter’s tape. Lay the tape flat against the wall, right where the wall meets the ceiling. Apply the tape in 2-3-foot strips for ease of handling.

    Cut-in onto the Ceiling.

    This is not a mandatory step; some experienced painting professionals skip it in favor of saving time. However, if you’re new to this, you don’t want to bypass this helpful trick. Cutting in essentially involves using a paintbrush to paint a strip of about one foot in width along the edges of the ceiling. Doing this will help you avoid smashing the roller on the edges and in corners because it builds up excess paint in the corner and can leave a thick paint line on the ceiling. After cutting in, you can go ahead and apply the paint using a roller on the rest of the remaining ceiling surface.

    Bottom Line
    Painting the ceiling can be a tedious process, but following the above tips will make the project less of a hassle. However, if you don’t have the painting skills, experience, and tools, painting your ceiling is definitely not your best first trial project.

    Hiring a professional painting contractor such as Serious Business Painting Company can save you the hassle and money, and provide clean, durable and beautiful results. We are currently serving the areas of Louisville, Shelby County, Oldham County, Anchorage, Prospect, and Jefferson Town, Kentucky. Book a free estimate below or give us a call today for more information.

    In the Victorian era, ceiling medallions were an important part of home decor, often used as the base for light fixtures and always giving the rooms they occupied a sense of elegance. You can still find ceiling medallions at home-improvement centers. They are made of polyurethane, wood, plaster, or metal and come in various shapes, such as flowers, stars, circles, ovals, and squares.

    If you have a ceiling medallion that doesn’t match the colors in your room anymore, you can paint it. This requires a little bit more care than an average painting project but is manageable if you follow these steps.

    Step 1—Get Ready

    Put a tarp on the floor under the medallion. Use a step ladder to gain access to the medallion. Tape off its borders. Remove the light fixture in the center as well and tape off the resulting cavity.

    Step 2—Spray Paint the Surface

    Before using spray paint, make sure the room is well ventilated, that you wear a respirator and safety goggles or glasses since you’ll be looking up while spraying. Shake the spray can to mix the paint thoroughly and apply a light coat of flat spray paint. For an even coat, keep the can of spray paint at least a foot away, and don’t linger in one spot but constantly keep moving with it to avoid buildups. Put on a second coat after an hour.

    Step 3—Start Painting

    Once the spray paint has dried, paint the features one by one with a small paintbrush. Wipe away any mistakes with the appropriate solvent or cleaner on a paper towel.

    Step 4—Be Careful With Multiple Colors

    When using different colors, let each one dry before applying the next one. You don’t want them mixing on the medallion unless intentionally blending them in, or if you’re antiquing the medallion..

    Step 5—Add the Final Touch

    To highlight the borders of your ceiling medallion you can add a touch of white. Use a small brush for this delicate work.

    In the world of painting a home’s interior, the roller method reigns supreme. It’s so easy, anyone could do it. There’s no complicated setup: Just prime the wall, paint, let dry, paint again, let dry again, and you’re done.

    An alternative painting method is using a sprayer, and it takes much less time. The downside: You won’t have a clue as to how to use it. Should you try it anyway? Rick Watson, director of product information and technical services at Sherwin-Williams, strongly recommends that if you have no experience using an airless sprayer, you must review and be well-versed in its safety procedures before taking on the job. Here, we explain the differences between a roller and sprayer so that you can decide which is better for you.

    Equipment Needed

    For roll painting a wall, you will need a nine-inch roller, an extension pole (if painting the ceiling), a paint tray, painter’s tape to mask off areas you don’t want to get splattered with paint, and drop cloths. This is the most affordable option. For a sprayer, you will need a sprayer (which is more costly), painter’s tape, drop cloths, and a face mask.

    Ease of Use

    A roller is beginner-friendly, so no previous experience is needed. When it comes to a sprayer, you’ll need to learn how to use the sprayer safely and effectively, which can be time-consuming.

    Number of Coats

    With a roller, you need to prime walls before painting and a second coat of paint is highly recommended. Comparatively, in using a sprayer, there’s usually no need for a second coat. “But even with a perfect spraying technique,” says Watson, “it’s often recommended to back-roll to hide imperfections or to provide a smooth, attractive finish.” (“Back-rolling” means to use a paint roller to press the paint just applied into the wall.)

    Cautions

    When using a roller, be careful if using a ladder. When using a sprayer, always wear a face mask or respirator while spraying. Be aware of dangers; for example, the high pressure generated by an airless sprayer could pierce your skin and inject toxins into the body, says Watson.

    Time Required

    A roller will take the better part of a day, then part of the next day. Compare this to the expediency of a sprayer—once you get the hang of it, painting may only take a few hours.

    Cleanup

    Painting with a roller is easy and so is the cleanup. Once you’re done for the day, clean brushes with a garden hose or in sink. However, cleaning a sprayer can be time-consuming. You have to constantly clean the sprayer to prevent clogs.

    Painting a drop ceiling is something we do on a regular basis. It is not difficult but it can take more prep work than usual if it is in an occupied space. Dropped ceilings are the ceilings installed below the structural ceiling and are commonly comprised of acoustical ceiling tiles and a network of metal grids and wall channels.

    How to paint a ceiling with a sprayer

    By the nature of the ceilings construction, it must be sprayed. When we are doing a ceiling we tend to use a latex dryfall material. Dryfall is a paint that “dries as it falls” and is manufactured to dry at various fall distances. For example you can buy 8 foot dryfall, 12 foot dryfall, etc. These are paints that dry when falling 8 feet and 12 feet respectively. The dryfall distance is theoretical and dependent upon the environmental conditions such as temperature and humidity. Even though the paint should be dry we always take measures to limit the surrounds to over-spray. This includes protecting the floor, walls, etc.

    How to paint a ceiling with a sprayer

    After everything is protected from over-spray, we will go through and seal any stains on the ceiling. We normally use a shellac based sealer since it dries very fast and is very effective.

    One of the most important factors when spraying this type of ceiling is to look at it from several different angles to insure proper coverage. When painting a drop ceiling we usually have 2 or 3 different employees look from all possible angles to make sure everything is completely coated.

    How to paint a ceiling with a sprayer

    After we are certain everything is coated we will do a second finish coat for good measure.

    How to paint a ceiling with a sprayer

    The nice thing about taking all the time it takes to cover everything up is clean up is fast and much easier. The biggest challenge is disposal of all the masking materials.

    Sharing is caring!

    • Pin
    • Share
    • Tweet

    Make designing your dream room a breeze with my Printable Room Planner.

    Learn all about how to use a paint sprayer using the HomeRight Super Finish Max Extra sprayer.

    I love painting. Nothing makes me happier than having a paintbrush in my hand. I know it’s weird, but I enjoy the process. However, every now and then, there are projects that I don’t enjoy painting. Like spindles. Or wrought iron furniture.

    After my husband professed his desire for a rocking chair for the patio, I picked one up at a thrift store for him. All of those spindles made it the perfect candidate for my new HomeRight Super Finish Max Extra sprayer. Learn how to use a paint sprayer. Painting all of those spindles was quick and easy with the right tool!

    How to paint a ceiling with a sprayer

    My First Project:

    How to paint a ceiling with a sprayer

    Don’t let the picture fool you. This is not wood, but a lovely almost neon orange with a faux finish over it. There were also varnish bubbles and drips in select spots. After sanding down those spots, it was time to get ready for spraying.

    By the way, when you buy a rocking chair, a lot of vintage items and a Scrabble game, the guy at the thrift store will probably make fun of your grandma ways. Haha! He has no idea.

    How to Use a Paint Sprayer

    This post contains affiliate links. By purchasing an item through an affiliate link, I earn a small commission at no extra cost to you.

    Supplies Needed

    • HomeRight Super Finish Max Extra Sprayer
    • Plastic drop cloths or spray shelter
    • Paint

    Easy Tips for Using a Paint Sprayer

    Wondering if you should use a sprayer for walls? Find out.

    Pin for Later!

    How to paint a ceiling with a sprayer

    How to Use a Paint Sprayer

    How to paint a ceiling with a sprayer

    How to paint a ceiling with a sprayer

    Emy is a vintage obsessed mama of 2 DIYer who loves sharing affordable solutions for common home problems. You don’t need a giant budget to create a lovely home. Read more…

    Reader Interactions

    Comments

    rane Lederer says

    January 01, 2018 at 7:40 am

    Looks great! I suppose, if you’re super anal, the bumpy parts could be sanded and sprayed again, right? It’s still faster than brushing by hand, that’s for sure!

    January 27, 2018 at 9:54 am

    Think you! This is very helpful and definitely going to use them when using my sprayer.

    January 29, 2018 at 10:11 am

    Thanks Mary! My husband used the sprayer and he loved it so much. Start with something not precious until you get the hang of it. It’s so easy to use once you figure out the right spray setting. (We also learned not to turn it all the way to the minus sign or it wouldn’t spray at all.) Good luck!

    Leave a Reply Cancel reply

    This site uses Akismet to reduce spam. Learn how your comment data is processed.

    Primary Sidebar

    Let’s be friends!

    • Facebook
    • Instagram
    • Pinterest
    • Twitter
    • YouTube

    Looking for Something?

    Hi, I’m Emy!

    How to paint a ceiling with a sprayer

    I’m a color loving DIYer who believes that a beautiful home is possible, even on a budget.

    Follow these simple painting tips to freshen up your ceiling.

    How to paint a ceiling with a sprayer

    Related To:

    Nothing brightens a room like a fresh coat of paint. If you want to completely makeover a room, start with the ceiling before you paint the walls. It may seem like a messy, daunting task, but designers say painting a ceiling is well worth the effort. “We consider ceilings the fifth wall,” says Miranda Cullen with Duet Design Group.

    We’ve uncovered expert advice on how to paint a ceiling that will make the job a cinch. Follow along for a step-by-step approach to the perfect paint job.

    How to paint a ceiling with a sprayer

    Pulling It All Together

    Carry the new color of your ceiling throughout the space by choosing pieces that are a similar shade — like the velvet green bench and the plant life in this photo.

    Photo by: Jalynn Baker

    Supplies and Materials

    • paint
    • extension pole
    • paint roller and cover
    • paint tray
    • step ladder
    • drop cloth
    • painter’s tape
    • angled paint brush
    • 100-grit sandpaper

    Tip: Roller extension handles make it easy to paint regular ceilings without constant bending and stretching. To paint the trim, remove fixtures and reach high ceilings, you will also need a step ladder.

    Step 1: Choose Your Ceiling Paint

    Flat or matte finishes are most often used for ceilings as they will hide imperfections. Paint made specifically for ceilings is designed to roll on with minimum spatter and will resist yellowing over time. And of course white is a popular ceiling color as it reflects light into a room. But clearly there are color options.

    “Ceilings are often an afterthought, but I like to accent them because it can really change the entire mood of the space. Highlighting them with a dark color or a patterned wallpaper all of a sudden elevates the entire design,” says Kelly Sutton of New Orleans-based Sutton House.

    How to paint a ceiling with a sprayer

    Paint Glossary: All About Paint, Color and Tools

    Learn what type of paint to use, which tools will work best and the basics for picking color schemes.

    Step 2: Calculate How Much Paint You Need

    Before you get started, you’ll need to calculate how much paint you’ll need. Measure the length and width of the room to get the square footage of the ceiling. Paint cans are labeled with the area they should cover, so you can easily buy accordingly.

    Step 3: Prep the Room

    The best paint job starts with prep work. Follow these tips:

    • Remove artwork from the walls and obstacles from the floor to avoid accidents.
    • Take small items to another room until the painting is complete.
    • Large furniture may be covered with a drop cloth.
    • Remove light fixtures, ceiling fans and any other obstacles attached to the ceiling. Be sure to clean fixtures before replacing them on the newly painted ceiling.

    This is a great time to update old fixtures. Vacuum textured ceilings to remove dust and cobwebs. Clean nontextured ceilings with a sponge using mild soap and water.

    Step 4: Patch and Prime

    Fix any damaged parts of your ceiling before applying paint. Also patch any holes in the ceiling and sand them smooth. (Learn how to patch a ceiling). Sand non-textured ceilings with 100-grit drywall sandpaper to ensure good paint adhesion.

    How to paint a ceiling with a sprayer

    How to Repair Cracks and Holes in Drywall

    Learn six ways to repair drywall depending on the size, type and place of the damage.

    Use a stain-blocking primer paint to cover patched areas and watermarks.

    Today I’m showing you my trick for how to paint drop ceilings you cannot remove – or maybe don’t want to remove. I think I am the least glamorous blogger. Other interior design and DIY bloggers are doing major renovations with fabulous, luxury finishes like marble and hardwood, and I’m over here painting my janky drop ceiling. In fact, I’m giving my basement the cheapest makeover in history. Truth be told, I hate these drop ceilings but we do not have the budget to replace them, so I had to figure out how to decorate around our drop ceiling. I decided to paint the drop ceiling the same colour as the walls, so the ceiling will no longer stand out and the basement will look cozy and warm. A drop ceiling with paint will just blend in – that’s my logic! (Plus, I’m not going to lie, I’m too lazy to cut in neatly around that darn drop ceiling). This basement will never feel tall or spacious so there’s no sense fighting it; I’m going to emphasis its small size and make it feel cozy instead.

    How to Paint Drop Ceilings You Cannot Remove:

    We tried removing the ceiling tiles, but the way our drop ceiling was installed, ours only move side to side (to access pipes, etc) so taking them down would have required dismantling the entire framework (too much work). After much cursing, tugging and general wriggling, trying to get the ceiling tiles to slide out, we gave up. Next idea. I tried painting them in place, like a regular ceiling, but the paint made the tiles stick to the frame and when they shifted a bit, I had weird cracks and peeling paint. It looked cheap and awful. Arrgh. More swearing. Next idea. With Hubby building walls and a nice, not-drop ceiling in the next room, I eyed some of his furring strips and we came up with this solution for how to paint drop ceiling tiles that cannot be removed:

    1. Prop up a few ceiling tiles with furring strips
    2. Using a large paintbrush, paint the edges and the frame holding the tiles
    3. Once paint is dry, drop the tile back
    4. Using a roller, apply paint to the middle of the tile

    How to paint a ceiling with a sprayer

    It’s more consuming to paint drop ceilings this way, as opposed to just using a roller and painting it like a normal ceiling, but painting drop ceilings by propping up tiles created a much better finished product – it’s neater looking.

    How to paint a ceiling with a sprayer

    You can already see at this point of the project, by painting the drop ceiling it’s blending in so much better with the walls!

    How to paint a ceiling with a sprayer

    Here’s a sneak peek at the finished project after I figured out how to paint drop ceilings without removing them – the color changes a lot with the light but it’s more of a cool greige than a warm tan.

    How to paint a ceiling with a sprayer

    Success! I’m loving the painted drop ceiling because it blends it. I’m really thrilled with how well my bizarre hack for how to paint a drop ceiling that can’t be removed worked, although I could only do about 6 tiles at a time – unless we were to splurge on some extra furring strips. Hubby was quickly finishing his work in the laundry room, so I was against the clock painting the drop ceiling at a quick pace before he needed the wood back, haha!

    How to paint a ceiling with a sprayer

    What Paint Do You Use on Drop Ceiling Tiles?

    I used a good quality primer and paint in one, so this job is fairly straightforward and only required one coat in most spots. For this project, you definitely want to speed up the process so I recommend good quality paint – you can use exactly what you’re using on walls, or a ceiling paint for a more flat/matte finish. But either use a primer or buy paint and primer in one!

    So that’s my quick tip for how to paint drop ceilings that you cannot remove! I hope you find this helpful, and that it makes painting your own drop ceiling tiles easier.

    How to paint a ceiling with a sprayer

    The Finished Basement Makeover

    Here’s a reminder of the basement before:

    How to paint a ceiling with a sprayer

    And now here’s a look at the finished basement makeover (see more of this space here or find all of the basement makeover progress here)! This was a very inexpensive makeover, using mostly paint and furniture we already had – but the end result is clean and cozy. Perfect! And you can see the painted ceiling tiles look great too.

    How to paint a ceiling with a sprayerHow to paint a ceiling with a sprayerHow to paint a ceiling with a sprayer

    We carried the same paint color into the laundry room – but painted the concrete floors a fun aqua! See more of the laundry room makeover here.

    Have you ever finished painting a ceiling, and it looks absolutely beautiful but then you spot very visible roller marks on it, and it just seems to immediately ruin the whole painting?

    Frustrating right? Many painters share the same experience. Visible roller marks on the ceiling after painting can be quite an eyesore and you do not want such a seemingly unimportant defect to ruin your entire painting, do you?

    Well, this article is going to provide some simple yet important steps that you can take to get rid of the nuisance of visible roller marks on your ceiling when painting.

    Steps To Take To Avoid Visible Roller Marks When Painting

    Now I am going to share some useful tips and steps you would want to take to avoid having visible roller marks on your ceiling while painting.

    A brush and a roller and the two basic things you use to paint a ceiling, so we will also see how we can utilize these tools to your advantage and not disadvantage.

    1. Use a light glaze or sheen: Sheen is the amount of shine or glazes that paint has or shows after paint. When choosing the paint that you want to use to paint a ceiling you should pick paint with a flat sheen

    Why? Because paint with a high sheen such as satin or gloss paint, will shine out brightly and this is not good for the ceiling paint because it brings out the unnoticeable mistakes on the painting just like roller marks, making them stand out and probably ruin the ceiling painting.

    2. Make use of thick roller naps: unlike a common misconception among most paint companies, thick roller nads are good for painting ceilings and other places.

    This is because they help to avoid roller marks when you are painting.

    A nice tip for using thick roller naps is that you should fill over an area you are painting and then go back and roll over it again, then drench your thick roller nap in paint again to collect more paint.

    Thick roller naps help you avoid roller marks when painting due to their thickness. It has round, full, and soft edges, which aids painting because it

    applies the paint well. While thin rollers might end up leaving marks on the ceiling because of their sharp edges.

    3. Take less paint on your roller nap: when there is too much paint on the roller nap at once it may cause it to start showing roller marks on the painting.

    But if the roller marks appear already you can solve the problem but reducing the paint on the roller nap and then re-roll on the areas that have roller marks on them

    4. Use an opposite rolling pattern: when you are painting a ceiling, there is a technique that has proved itself helpful to me and others. Which is, for you to roll on two coats of paints in opposite directions from each other.

    After painting the first coat on the ceiling in one direction, allow it to get dry and roll it again in opposite direction. This is will help to ensure an even distribution of the paint on the ceiling.

    Because one of the common causes of roller marks appearing while painting or after the painting is due to light painting or uneven painting of the ceiling.

    So by coating the ceiling a second time with paint, it ensures you a clean, flawless, and roller marks-free ceiling.

    5. Secure a nice finish by spraying: spraying your ceiling after painting is the final touch that you need to give your ceiling a splendid,and spotless finish. When you spray your ceiling after painting, it gives you an even refined look.

    You do not need to spray close to the ceiling, you should do so at a considerable distance. You could also apply two coats of spray paints to give it the final flawless look.

    In summarization, we have considered some steps you should take to avoid roller marks on your ceiling while painting. If you carefully follow these guidelines and tips then you can avoid ruining your ceiling paint in any way.

    In this article, we will discuss: Can you paint the RV fabric ceiling? We will help you make your RV fabric ceiling look like any and explain why you don’t need to paint your RV ceiling at all.

    Can you paint the RV fabric ceiling?

    You can try to paint the RV fabric ceiling, but it is not really recommended. If your RV ceiling is old and stained, you should give it a good wash first! If the situation is really bad even after a thorough scrubbing, you could apply a thin coat of paint using a consistent amount of pressure.

    This being said, here are your three option:

    1. In general, it is impossible to paint an RV fabric ceiling due to its flexibility and fragility. Some people have tried glycerol and a paint gun, but they were not satisfied with the results. Remember to use a thick coat of paint!
    1. Instead of painting the RV fabric ceiling, it is better totry to clean the ceiling with chamois leather. You just have to immerse this rag in a little water so as not to damage all the paint on the ceiling.
    1. From an aesthetic point of view, however, it is better to have a clean fabric ceiling installed. It can be more expensive than painting, but before making a choice, you should first ask for a decoration estimate and think about the different advantages that the replacement can bring.

    A fabric RV ceiling is a synthetic fabric that is stretched with a spatula in invisible profiles attached to the walls. The fabric ceiling is installed under the existing ceiling.

    There are two types of fabric ceilings: polyester ceiling and PVC ceiling. The PVC stretch ceilings we install are anti-static, do not attract dust and are not porous. So it’s not a good idea to paint them. The polyester version can in principle be painted, but the result often leaves much to be desired. This is because they are often not stable enough to apply an even coat of paint.

    Why you don’t need to paint your RV fabric ceiling

    Often the ceiling is painted because it is yellowing or because it is stained. However, as we mentioned above, it can be quite difficult to paint over the fabric and to get good results.

    It is best to remove dirt from the ceiling by rubbing gently with a soft cloth and a little water. Follow our tips to learn how to clean your RV fabric ceiling and make it look like (almost) new!

    How to make your RV fabric ceiling look like new

    For a good professional cleaning of your RV fabric ceiling, you need the right tools and the right products:

    • 1 all-purpose cleaner (such as Invisible super cleaner by Chemical Guys) or 1 carpet and fabric cleaner
    • 1 carpet and fabric brush
    • 1 brush with fibre bristles for delicate areas
    • 1 microfiber cloth
    • Cleaning a task on the headliner

    There are 3 things you should keep in mind:

    1. Do not over-saturate the fabric, as this can soften the glue and peel the fabric
    2. Do not use excessive heat, as it may melt the glue
    3. Do not use excessive force, as it may damage the glue

    For so-called normal stains, a microfiber towel and a few squirts of your favourite interior cleaner should suffice. Always spray the product on the microfiber and not directly on the headliner.

    If that doesn’t work or for any other task, using the soft bristle brush (or paintbrush) is a good way to start. As we often remind you, the less you do, the better. If the brush is enough, look no further.

    Spray a cleaning product directly into the bristles of the brush from the end. Make light circles on the stain to lift the dirt, the product should foam and you can then wipe it off with your microfiber cloth.

    Warning: do not rub hard with your microfiber cloth, but prefer to press down by making small rotations, because sometimes the fabric of the headliner is much more fragile than the fabric of the seats. Again, less is more!

    Always work as precisely as possible on a headliner, so as to close as possible to the task at hand.

    As with cleaning a stain, spray a cleaning product such as APC (All Purpose Cleaner) or special fabric and carpet cleaner directly on the bristles of a fabric brush. Lather the product, then wipe with a clean microfiber cloth. Always with lightness.

    You can use your steamer, but do not bring the nozzle too close to the surface for too long. Using a steam cleaner should be a last resort in your mind.

    The Larry Kosilla Method for cleaning the RV fabric ceiling

    Another very effective technique to clean an RV fabric cleaner is to use your polisher with a microfiber pad such as the Meguiars Cutting Pad.

    You spray cleaning foam using a manual pump sprayer like the IK Foam 1.5 and run the polisher at low speed (2 to 3). The foam dries up and you can clean the ceiling without risking damage to the glue now.

    This method is very effective if you have large portions to clean. You can also take the opportunity to run the polisher over the sun visors.

    Never spray the cleaner directly on the ceiling! Indeed, this is why the detailing pros (and you now) spray the product directly on the bristles of their brushes to clean the ceiling because the product could damage the glue that fixes the ceiling to the sky roof.

    The bottom line

    Painting an RV fabric ceiling can be a quite difficult task. Our recommendation would be to call for a specialist. But before you do anything, try giving the ceiling a good wash! You may be surprised by the results and let go of the idea of painting it in the first place!

    Please let us know if you have any comments, tips, or questions about this content.

    FAQ on Can you paint RV fabric ceiling?

    Are the RVs spray or roller painted?

    Rvs can be both spayed or roller painter, if you know how to use the spray gun, go ahead since the paint is the best, but it is more frequent if you do it at home with a roller.

    Is any roller suitable for painting an RV?

    Not any roller is suitable for painting an RV. It has to be lacquer or velour roller of about 20 or 25 cm in length, although it can also be used smaller.

    Is it mandatory to paint the RV white?

    No, it is not mandatory to paint the RV white. Paint your RV whatever colour you want!

    How to paint the interior of a trailer?

    Apply one or more coats of primer using a roller. You can use a primer designed for exterior and interior for its properties resistant to temperature changes. Some surfaces require an alkyd-based primer.

    How to paint the interior of a motorhome?

    The solution then involves “home staging” adapted to the motorhome. This is what GSDI offers, by applying a plastic film to all or part of the furniture or bodywork. For this transformation, we keep the furniture and rather than repaint it, but we apply a new decoration.

    What wallpaper for a caravan?

    You can use non-woven paper, with ad-hoc glue. The advantage of the latter is that it suffers less from the pangs of humidity.

    How to paint a ceiling with a sprayer How to paint a ceiling with a sprayer

    Painting your ceiling can seem like a tough task. But following expert ceiling painting tips and using Benjamin Moore ® Waterborne Ceiling Paint can help you get the job done right.

    The Best Way to Paint a Ceiling

    How to paint a ceiling with a sprayer

    Step #1: Prepare with the Right Paint & Tools

    To get started, you will need a 2½-inch angle sash brush, painters tape, a nine-inch roller, sleeve and pan, an extension pole, a step ladder and Benjamin Moore Waterborne Ceiling Paint.

    In addition to your paint, make sure your brush and roller sleeve are high quality and that your roller sleeve is the appropriate nap for your ceiling texture. Ask your local Benjamin Moore retailer for help determining the best tools. When it comes to the best type of paint for ceilings, Benjamin Moore’s Waterborne Ceiling Paint is a “dead flat” paint that applies smoothly, hides most ceiling imperfections and is specially formulated to minimize both lap marks and splatter.

    Prepare with the Right Paint & Tools (continued)

    White is a common ceiling choice, but you can choose virtually any color to paint your ceiling, as Benjamin Moore offers thousands, and can match any shade.

    However, if white is your preferred ceiling color, INSL-X ® Color-Changing Ceiling Paint is a great choice. This unique paint applies in a light pink color that helps you identify missed spots, and then dries to a white finish with a flat sheen.

    How to paint a ceiling with a sprayer

    Step #2: Get the Space Ready

    A common question is: “What should I paint first, the ceiling or walls?” Always paint the ceiling before the walls, and always cover everything below the ceiling with drop cloths. Try to empty the room completely to make the job easier. Also, try to remove overhead light fixtures. If you cannot remove fixtures, use painters tape to protect them from spatter or use your brush to cut around them carefully.

    How to paint a ceiling with a sprayer

    Step #3: Prepare Walls & Ceilings with Paint

    Start with painting the edge of the ceiling where it meets the wall first. Cut the ceiling in like you would cut in a corner. Starting in the ceiling line, brush into the corner and feather paint 2-3 inches and down onto the wall. If you aren’t going to paint the walls, use painters tape to protect the wall or use the brush to cut in a nice straight line along the wall’s edge.

    Switch from brush to roller to start painting the rest of the ceiling. Start from the corner of the ceiling and start rolling nearest to a window, so that you can see the light from the window reflecting the wet paint. Then work your way across the room, rolling slowly when you’re near the wall to help avoid hitting it.

    How to paint a ceiling with a sprayer

    Step #4: Keep Your Roller Loaded

    Each time you load your roller, start on an unpainted area and work back into a painted area. Paint the ceiling in one session, so the paint dries uniformly. Wait for the coat to dry to determine if a second coat is needed. Check the label instructions for dry times.

    Your ceiling is refreshed and ready to fit in with the rest of your home’s interior design. For more ideas on ceiling color and design, check out Ceilings Ideas & Inspiration.

    Have More Questions? Visit your local Benjamin Moore store or contact Customer Support.

    Q:We have a “popcorn” ceiling that hasn’t been painted for more than two decades, and, although it looks fairly stable, it seems to be dropping powder, which we fear could be asbestos.

    We would like to know the most efficient way to paint this ceiling. We have heard that we could use a roller to cover it with a sealer (encapsulate the asbestos) and then a coat of paint. Others say the only way to do the job is to replace the ceiling. We have also heard that the best way might be to apply a layer of vinyl (a “French ceiling”). What would you advise?

    A: Handling asbestos is an important question that keeps surfacing.

    Asbestos is a mineral made up of microscopic fibers that look similar to fiberglass. Because of its strengthening, heat resistance and soundproofing qualities, asbestos was used to make pipe insulation, ceiling and floor tile, paints and coatings, caulking, fire-resistant fabrics and clothing and brake pads.

    It was outlawed for most residential uses in 1978, although builders were allowed to use stock on hand, so it’s possible that homes built as late as the early 1980s can contain asbestos.

    Asbestos is a health hazard when it decomposes and releases dust. When it’s encapsulated, it’s safe. As a precaution, we recommend you have your ceiling tested by providing a sample to a lab. For a list of accredited labs, go to links.sfgate.com/ZJNY.

    Over the years we’ve given three alternatives for dealing with the corn – paint it, cover it or strip it. All three methods work, and the choice should be based on the look you want. A French ceiling is also a possibility if you like the stretched-vinyl look (we don’t) and don’t mind the expense (we do).

    Removing the ceiling is a mess. Brother Bryan took this route. He covered the floor with drop cloths and spent the better part of a Saturday wetting the corn with water and scraping it off. Covering the ceiling with drywall can also be a do-it-yourself project. It requires a moderate level of skill and two strong people or a drywall lift. We explained the process in a column in 2004. Go to sfgate.com/ZJNZ.

    Of course if testing reveals asbestos, all do-it-yourself bets are off. Professionals in hazardous material suits will have to do the job at the cost of a pretty penny.

    Your ceiling is basically a large canvas. If you paint it dark, your room will feel cozier and more intimate while a light-colored ceiling will help your room feel larger and more expansive. A fresh coat of paint can also make your room more stylish and cover stains and imperfections. Despite this, the ceiling is often ignored when homeowners embark on DIY painting projects because they’re intimidated. Who can blame them? Painting the ceiling not only involves awkward arm positions and painting over your head, but if you make a mistake, you also run the very real risk of getting paint all over your floors, furniture, and even yourself. To alleviate those concerns, we went to Houston-based real estate investor Marina Vaamonde of HouseCashin to find out how to paint your ceiling without making a giant mess.

    Move the Furniture

    Before you begin painting your ceiling, Vaamonde suggests moving as much furniture as possible from the room. Large pieces, however, can be pushed to the center of the room and covered completely with drop cloths. Pro tip: Inexpensive furniture sliders will make it easier to move heavy pieces without damaging your floor.

    Cover the Floor

    Since you don’t want to get paint on your floors, your next step is to cover them with drop cloths. After you’re through, tape the edges of the cloths to your baseboard with painter’s tape.

    Remove Your Light Fixtures

    Next, Vaamonde says to direct your attention to the ceiling. If there are any light fixtures there, remove them if possible. If you aren’t able to remove them, cover them in cloth or paper to protect them from dripping paint.

    Protect Your Clothes

    This is not a project you want to undertake wearing your Sunday finest. Be sure to wear something you won’t mind getting dripped on with paint or buy a disposable suit to protect your clothing.

    Protect Your Walls

    Next, protect your walls. Vaamonde says the easiest way to do this is to stand on a step ladder and run painter’s tape all along the top of your wall next to your ceiling. Then, paint a three to four inch border around the ceiling to create a buffer between your workspace and the walls.

    Use the Right Equipment

    After you’ve protected your walls, Vaamonde says you can climb down from the ladder to complete the rest of the project from the floor with an extended roller. She also says a roller shield will help protect you and the room from excess spattering or drips.

    Take Your Time

    According to Vaamonde, most DIY mistakes and messes occur when you’re working in haste. She says, “Rolling paint too quickly causes spray to fly everywhere. Be deliberate with your roller strokes and don’t use too much paint.” This will make sure you get a nice, even coat on your ceiling without splattering everywhere.

    Allow the Paint to Dry

    Paint will easily transfer to anything it rubs against during the drying phase, so be sure to give it plenty of time to dry before you put your room back together. Since different paint types have different drying times, be sure to read the label to determine when it will be safe to remove the tape, replace the light fixtures, and enjoy your new room.

    Home » Basement Ceilings Painted BLACK – A Spray Painting Job from Hell…

    Share this:

    • Click to share on Facebook (Opens in new window)
    • Click to share on Twitter (Opens in new window)
    • Click to share on Tumblr (Opens in new window)
    • Click to share on Pinterest (Opens in new window)
    • Click to email a link to a friend (Opens in new window)
    • Click to print (Opens in new window)

    First thing was first with the basement: tape anything off that needs to be covered and spray paint the ceilings black. If you read the Basement Planning post than you know we were considering a drop ceiling. In the end this just made more sense. It was a lot less costly and its a look we each like about a thousand times more. Drop ceilings only had one thing going for them: we could have insulated between the floors but it just wasn’t worth it for us.

    This is going to be our basement winter bar/our theater room/our great spot for over night guests in the future so, insulating between the floors wasn’t number one on our list. (Unlike if this had ended up a rental suite like my earlier plans.)

    I LOVE the look of these old basement ceilings, with their cross beams and rough cut 100 year old timbers, it would have really killed me to cover them up anyway.

    How to paint a ceiling with a sprayer

    How to paint a ceiling with a sprayer

    How to paint a ceiling with a sprayer

    How to paint a ceiling with a sprayer

    Lodi gets ALL of the credit here and, I’ll admit, I’m not the least bit unhappy I missed spray painting black paint over my head! I’ve done my share of spray painting in the past and fully understand how crappy a job it is. I rented a sprayer years ago and spray painted this entire house, ceilings, sheet rock etc.

    But though that was a bigger job it definitely paled in comparison to the SUCKAGE that was getting this done.

    For one thing the paint sprayer I rented back then was a lot bigger and didn’t require constant refilling or HOLDING 1/4 of a gallon of paint in hand while spraying it. The other thing it was a lot more powerful so I didn’t have to use a ladder at all to even do the ceilings.

    On top of that the ceilings I was spray painting were flat… these ceilings are just a nightmare to get into every nook and cranny.

    But Lodi got it done and used the new paint sprayer I bought as a treat for myself a few months ago. Honestly though, I wish I had skipped the purchase (though I’ll definitely use it in the future) and just rented a paint sprayer for this job.

    In the end he used four gallons of paint and it took him around six hours all together. Despite the crap job though he totally agreed it was worth it.

    I love how it made the ceilings just disappear!

    I am aware of how crappy the basement looks in these pictures lol we still have a ways to go on this space but I wanted to update you guys on where we were…. or, I should say, where Lodi is on this project!

    At this point I haven’t contributed besides my opinion and experience at all!

    Lodi stripped the place, cleaned it, taped it off and now has the ceilings complete. In the future I’ll be contributing a lot more – as an essential employee I was working so it just made sense for Lodi to be tackling house projects when he was stuck at home.

    I’m still trying to figure out the lighting plan – I’m leaning toward replacing all the bulbs with Edison bulbs and doing something really unique over that florescent light in the middle… or replacing the florescent light completely…

    I really think we made the right choice on these old ceilings! Can’t wait to show you guys the Rust-oleum RockSolid Garage Flooring we chose for this space!

    I have to prime and paint almost the entire interior of the house I am moving into. First I want to prime then buy a 5 gallon can of white to paint all the moldings and ceiling. Then mask it all off then roll with the color I want to use. Will this work.

    I just purchased an air compressor and if this idea works then I will buy the spray paint attachment.

    Thanks in advance.

    Hand rolling is the best in my opinion. I had one of those air sprayers before and it was more trouble than it was worth, plus you loose a lot of paint in the hose when you clean it.

    I would also suggest painting the walls first and then the molding.

    My dad has been a paint contractor for 40 years. I worked with him quite a bit unfortunately.

    You can spray the inside of the house if you mask off windows, and dont care about floors. It is typically done in new construction when priming as it is faster.

    However there are downsides..you will go through more primer/paint. You will have to water it down for the sprayer if not it will clog, and you will have to do several coats to get the same coverage as a roller.

    Next thing is you will want a good quality spray rig. forget the wagners they sell at home depot. If you dont want to purchase one then you can rent one.

    You will have to keep an eye out for runs, if you get to much paint/primer in one area its easier to clean it up while its wet then when its dry.

    The ceiling fan belongs largely to your home decor. If you have a decent set in your home, the nut ceiling fan looks dirty; then it’ll dissolve your reputation and decor. That’s why always make sure that your ceiling fan is always clean. Are you curious and want to know how to paint a ceiling fan without taking it down. Yes, it’s possible. Here we’ll discuss the most exciting and easiest method you can easily do at your home. We also discuss the tips you must do before painting the ceiling fans.

    Supplies needed:

    • Screwdriver
    • Pouch
    • Marker
    • Sandpaper
    • Water
    • Bucket Of detergent
    • Ladder
    • Rustoleum Ultra Cover paint in Glos
    • Foaming sheet

    Steps To Paint A Ceiling Fan Without Taking It Down

    Let’s start our procedure:

    Step 1 : Turning off breaker

    Firstly, the most important instruction that keeps in your mind is turning off your breaker. Never make the mistake of turning on the breaker. Otherwise, it’ll cause severe results.

    Step 2 : Removal of blades

    The next step is to pick up the screwdriver. Using the screwdriver, start removing the blades of the fan. After removing the screws, place your screws in the pouch. If you remove the screws of more than one fan, mark each fan screw in the pouch. It’ll help you in identifying which screw belongs to which fan.

    Step 3 : Removal of metal brackets

    When you remove the screws, take the blade one by one and remove the metal bracket. Place the metal bracket in the relevant screws pouch. Make sure to put the screws and metal brackets of the same fans in one pouch.

    Step 4 : Use of sandpaper

    Pick up the sandpaper and fold it. Now clean the blades.

    Step 5 : Clean of the surface

    Firstly clean the sand grit area when it is thoroughly cleaned with warm water. If you still feel it’s not clear and wants more cleansing, then use detergent on it—detergent helps in removing grease or any remaining dirt particle.

    Step 6 : Painting the motor and blades

    Now it’s time to paint. Paint the motor area. You can use Rustoleum Ultra Cover paint in Glos for this purpose as it’ll give you excellent results. Similarly, paint the blades of the fan by using spray paint. If one coat is not enough, you can do two coats. Let it dry until it dries completely.

    Step 7 : Paint on the metal brackets

    Now use the spray paint to paint the metal brackets.

    Step 8 : Paint on the screws

    Punch all the screws of your fan in a foaming sheet. Then use the spray paint on them and make them dry for 5 minutes.

    Step 9 : The painted fan is ready.

    When every part of the fan will dry completely, join it back to the fan.

    All these steps will help you to paint the ceiling fan. It is the easiest method, and it also helps you in how you’ll renew your ceiling fan.

    Another Method

    Now move towards another method of how to paint the ceiling fan without taking it down.

    1. First, switch off the fan to work safely. Use a screwdriver for removing arms, blades, and light fixtures from the ceiling fan housing. Use multi-purpose spray cleaner or mild detergent and water for cleaning arms, hardware, and fan housing, including screws. Then, use a lint-free cloth to wipe all these components.

    2. Then, cover the work surface in a drop cloth and place arms, blades, and screws into it. Use painter’s tape to cover the ceiling fan housing. Make the screws stand upright by pushing their end into the cardboard piece.

    3. Take a metal primer. Apply one coat to the canopy, screws, blade arm, and ceiling fan housing using a foam brush. Then, give it some time for drying out.

    4. Take the paint used for the metal in any dish. You can use a small foam brush to paint on the ceiling. Use the brush to work the paint into vents or grooves. After applying the first layer, wait until it doesn’t dry. Then, apply a minimum of two or a maximum of three layers until you get the appearance according to your desire.

    5. Use a foam brush to paint the screw head and wait for some time until it dries. Now, take the same paint that you used on the ceiling fan housing. Apply it to the ceiling fan arms and make a minimum of two or a maxim of three layers using a foam brush. Always make sure that you apply the next layer after the first layer has been fully dried because, in the other case, you will get the worst appearance of the fan due to the mixing of paint.

    6. Take a primer that is suited for vinyl and apply it on the Paint vinyl fan blades. Make one coat and leave it until it dries completely. After that, use latex paint to apply another coat. Give it time to dry. Use a rag for wiping away the dust and sanding the blade. After finishing the second coat, pause the process for a short time to ensure complete drying of the second layer. Repeat the same process with all fan blades. Give it one day time to be dried completely.

    7. Take oil-based paint and apply it to the Paint wood fan blades. It depends on your choice that you’ll apply two or three coats. Apply the next layer after the first layer dries properly. Wait for one day before moving towards the next step.

    8. Now you have to wind up the process and get an attractive product. Fasten the arms with fan blades. Place the blades on the ceiling fan housing. If possible, fix the light fixture and unfasten the tape that was fixed around the fan’s canopy.

    Congratulations! After reading a small article, you have become professional in painting your old ceiling fan to the next level without removing it. The process is too easy, and the products are awesome but always make sure you follow all instructions properly, especially applying another layer after the first layer dries completely. You don’t have to wait for a professional and invest a large amount in their fee. Be creative and enjoy an amazing product you will create on your own.

    Painting tips from Which? Trusted trader, Extreme Handyman Fencing & Decorating Service’ Dene Walker will help you get your home decorating done in no time.

    You don’t have to be Michelangelo to paint a ceiling. Admittedly, it might help if you’re attempting something along the lines of the Sistine Chapel, but if you just want a couple of coats of emulsion, it’s definitely something you can tackle yourself. If the idea of painting above your head makes your shoulders ache, you can find an endorsed painter & decorator with Which? Trusted Traders to take it on for you.

    If you’re up to the challenge, ensure you have the right tools for the job. As a minimum, you’ll need:

    • a roller
    • a telescopic roller extension to avoid needing to use a ladder
    • a 2 or 3-inch paintbrush

    How to paint a ceiling with a sprayer

    The best paint for ceilings is a simple matt emulsion. Specialist ceiling paints do exist – they’re formulated to avoid spatter and dry slowly – but a simple white matt emulsion is fine for most jobs.

    Check our article on cleaning your paint brushes and rollers to keep your tools in top condition. Read on for more tips to ensure a smooth finish for your ceiling.

    Prepare the room

    You’ll need to clear and cover the area to avoid damage from drips or spatters. Remove as much of your furniture and ornaments as possible from the room, then cover the floor and anything you can’t move with dust sheets or protective plastic.

    How to paint a ceiling with a sprayer

    If you’re planning to protect areas you don’t want painting with masking tape, use the best tape you can afford, and be aware that it may still allow some paint underneath. An alternative is a painting shield, which costs about £5 and can be reused. You hold the shield with one hand to mask an area, while you paint with the other hand.

    Prepare the surfaces

    Planning and preparation is the secret to a professional finish when painting. With any decorating project, you start at the top and work your way down, so always work on the ceiling first.

    Start by scraping away any flaking paint or other lumps. Fill any large holes or cracks with a suitable filler product.

    If there are stains on the surfaces, such as grease or watermarks, these need treating with a shellac-based stain blocker product to seal them in, before you start painting.

    How to paint a ceiling with a sprayer

    For hairline cracks in the ceilings or walls use a knife or old screwdriver to enlarge the crack slightly before filling. Giving the filler more space means it won’t fall out as it dries.

    If you need to deal with a hairline crack in a corner or around woodwork, use a cartridge gun to apply decorative caulk (not silicone). Squeeze it into the gap and carefully smooth it with a wet finger or sponge. Allow it to dry according to the manufacturer’s instructions – you can overpaint most varieties within an hour.

    All surfaces must be clean, dust-free, and completely dry before you start.

    Cover any light fittings in the ceiling with low-tack masking tape to keep them free from paint. If you’re planning to paint the walls next, you may want to cover the wall fittings at this stage, too.

    Painting the ceiling

    Once the walls are ready you can prepare the paint. Dilute the paint with water or commercial thinner by 10% to reduce the ‘orange peel’ effect left by rollers.

    Use a medium pile roller, with a telescopic roller pole, that holds enough paint to cover a large area at a time. Work across the width of the room for the first coat and along the length of the room for the second, working away from the direction of the light. Always leave four hours between coats to avoid peeling in the future.

    Ensure you keep a wet paint edge while you are working, otherwise you will get a ‘shut’, which is a line created where you overlap and have let the leading edge dry. This means that once you start, you cannot stop until the wall or ceiling is completed.

    How to paint a ceiling with a sprayer

    If the ceiling starts peeling then stop painting, as the roller will cause more damage and deposit the peeled paint onto other area which will ruin all your hard work. You will need to paint the ceiling with specialist anti-peel paint before reapplying the top coat.

    Always cut in (paint the areas that are too tight for large rollers) while the ceiling is still wet. You can quickly get around the ceiling edges using a 2-inch brush or a mini roller – a small step or ‘hop up’ will help with this.

    Try to avoid getting paint down the walls, even if you are going to paint them afterwards as the white ceiling paint may ‘flash’ through the new wall colours.

    Allow the paint to dry before removing any masking tape from around fittings.

    Painting newly plastered surfaces

    If you’re working with newly plastered ceiling or walls, or you’ve filled any holes, start by painting a mist coat. A mist coat is a matt emulsion, thinned right down with water or a commercial thinner, to seal the surface and provide a strong base for the top coat of paint to stick to. Never use emulsions with vinyl for a mist coat. You can buy paints designed for new plaster if you don’t fancy mixing your own. The mist coat will reveal smaller imperfections that you can tackle with filler and sand flat. You may need more than one coat to cover the wall evenly.

    It is a good idea to do a mist coat under any strong colour change, particularly if you are going over reds or blues.

    Painting walls

    If you needed a mist coat, wait for it to dry before applying the first coat. Check the manufacturer’s guidelines for ventilation, drying time and other instructions and once again thin the paint slightly. Paint with vinyl in it is more durable and preferable for heavy-use areas. Apply at least two coats – several light coats of paint are usually better than one heavy one. Painting in daylight will help you to avoid getting a patchy finish.

    Once again, roll the main body of the wall first. Use a paint tray and apply the roller with gentle, steady pressure. Be careful not to overload it. When the roller stops sounding ‘wet’, reload it with paint.

    Roll one wall then cut it in whilst it is wet before proceeding to the next wall. Start at the top and work your way down. Begin by ‘cutting in’ (using a paint brush to cover the areas that are too tight for rollers) at the ceiling line, painting each wall methodically. Use firm, horizontal strokes in line with the ceiling for a straight line. If you’re working on a vertical join, you may find it easier to rotate the brush to paint with the narrow side.

    How to paint a ceiling with a sprayer

    If you’ve used masking tape, peel this off gently while the wall is still wet before starting on the next wall. If paint seeps through the tape, wipe away with a damp cloth.

    If you’d rather a professional painter and decorator took the strain, Which? Trusted Traders has accredited traders in your area.

    Your home or apartment is a place that you want to keep nice at all times. You want to make sure that the interior and exterior of the place is as nice as possible. One of the things that you have to make sure is really nice is the interior of the residence. This may take spray painting of the walls and the ceiling by using a paint sprayer for interior walls.

    How Do You Spray Paint Interior Walls And Ceilings Today?

    How to paint a ceiling with a sprayer

    Your interior walls and ceilings need to be spray painted in a good way. You should make sure that you have all the necessary supplies so that you can get to them in the right way.

    It will be easy once you get the hang of it because you will find that it is easy to get it all done in the right way. Since there is so much that you will need to do, take it slow and easy so that you can get the walls and ceilings to look just right.

    Pick The Colors That You Like

    You will want to pick the colors that you like for your walls and your ceilings. Make sure that you match them well with the rest of your interior.

    It will make a huge difference when you are in your place when you like your surroundings. You will feel wonderful when you have all that you need in your new place so that you can relax and enjoy being at home.

    Be sure that you will get all that you need to make sure that you have all the necessary supplies to complete the job.

    Furniture Is A Must In Your New Place

    The furniture that you pick is important. You want to be as comfortable as possible when you are moving into your new place.

    Make sure that you get the items that you need and also that they are practical for the purpose that you need them for.

    How to paint a ceiling with a sprayer

    With all that it will take to get a great place, you will be able to have what you need to make you feel right at home.

    Don’t spend more than you can afford but get the things that you need in order to do it the right way.

    When you are all settled in your new place, you will feel a lot better. Make sure that you can get everything that you need in place when you can.

    Since this will make you feel a lot better about everything that is happening to you, you will get what you need at the time that you do. Your new place should be unique to you and you will want to make sure that you have everything in order.

    It will take a bit of time and you will need to concentrate on many things at once. The thing is it will all get done in a short period of time and then you can enjoy it.

    You will really love living in your new place when you are done.

    We just purchased a house and before moving in we want to paint all the rooms: 4 bedrooms, living room, kitchen, and family room (2000 sft home). Being we want to be as efficient as possible I had looked into using a power sprayer. I’ve read both pros and cons on doing this so hoping to seek some answers from people here that have done this before.

    So, using a sprayer inside, yes or no? If yes, what tips and precautions would you suggest?

    3 Answers 3

    Pro: Quick TO PAINT. ONLY.

    Con: you have to mask everything, but EVERYTHING, you don’t want covered in paint. Floors, windows, toilets, sinks, outlets, switches, lights, the works.

    Con: not good if you want more than one color, or yet more masking needed.

    Apartment complexes that paint everything white and replace the carpets (and nearly everything is carpeted) afterwards find them “efficient” – most other people get the whole job done a lot faster with a roller and brushes.

    How to paint a ceiling with a sprayer

    When I did my house, I used a sprayer. But everything was getting ripped out, floors, doors, trim and light fixtures. Masking was simple because of this and being able to do the entire house in about 8 hours of work over two days paid for the extra paint and sprayer. This was a coat of primer and 1 to 2 coats of paint. The 3 rooms I didn’t spray was the kitchen and bathrooms. If was going to repaint a room now, I would go with a brush and roller.

    When I say extra paint, I mean extra paint. I used about 25% more paint than I would have if I used a brush and roller.

    If you plan on doing A LOT* of painting, then yes; use a paint pump with a roller attachment.

    Electric Airless Paint Sprayer:

    How to paint a ceiling with a sprayer

    *A LOT= You are a painter or a landlord. Breaking down and cleaning these systems can take hours (if you expect it to work the next time).

    How to paint a ceiling with a sprayer

    All Topics / Value Adding / Painting vermiculite ceiling

    Anyone know of a painting service that does these very attractive 70’s-80’s ceilings. I have one to do but really dont want to buy into it……plenty to do elsewhere in the place for me. Location is Melbourne inner north. Thanks for any advice.

    Any painte rthat doe sspray painting can do it for you, but be warned-you will use a LOT of paint.

    OK thanks , I will try general painters, I assumed it was a specialist job. Yes , I have heard that stuff really soaks up the paint and needs sealing as one of the steps.

    You need to spray paint it because that is the only way those vermiculite things don’t break off. Another option you may like to consider is to install a fake dropped ceiling, then you can do downlights at the same time. Sometimes it works out cheaper, and it certainly looks better. You have to wonder what those people in the 70s were thinking don’t you. Another option is to paint the walls in a colour that tones down the vermiculite, a friend of mine recently did this painting her walls a soft moss green and it really camouflages the grey vermiculite, now you hardly notice it at all, whereas before when the walls were stark white it really stood out. Good luck.

    I actually stoped using spray for vermiculate ceilings. You need to put 5-6 coats of paint and there still all this little gaps in the structure that look dark on fresh paint. It also takes a lo-o-o-ot of paint. The amount of additional weight from the new paint that goes on those old ceilings could be really disturbing. I found that the gentle texture paint carefully rolled on gives much better results.

    As ZJ said, batten out the ceiling and install plasterboard and paint that. You will lose about 35-50 mm in height. Replace the existing light with a ceiling oyster unless you have enough height to install downlights. Remember that the ceiling height in most rooms (except halls, baths, laundry, storerooms or garages) must be 2400 mm minimum.

    thanks all, I will look at both solutions once we get access. I imagine battening the ceiling will involve some scrapping back along the batten line to get a flat surface to secure to. Think I have the height to play with OK.

    Found a lot of nice solutions for false cielings but as we are already at minimal hieght we decided to work with what we had. The ceiling was filthy (as was the rest of the place, its disgusting what people will live with and in at times), so we hired a steam cleaner today and cleaned it up to stage were we think it will take paint (working above your head all day is hard work I have decided). Durobond in Sydney make a specialist paint to cover and seal vermiculite. Have that in hand and will spray in a couple of weeks when I get something else out of the way. If necesssary it can be topped with normal ceiling white. Will post again when its done (good or bad)

    I only just read your post but we recently had some quotes done for painting our block, and the painter had just finished a job with these ceilings.

    Bondcrete
    is apparently what you’re after. Apply this first and then the paint will adhere to the surface.

    Paint will stick without bondcrete, but if you use some watered down bondcrete it will seal the surface so you won/t use as much paint.

    Hope you guys are aware that this stuff often contains asbestos especially 1970s vintage! So scraping might not be a good idea unless protective gear used. It was used particularly on the lower levels of residential blocks to give fire resistance (hence the asbestos)
    Was still imported from Canada marked non asbestos with 5% asbestos till 1990s.

    Asbestos Audits Queensland | Asbestos Audits Queensland
    https://asbestosaudits.com.au/
    Email Me | Phone Me

    Any asbestos questions ask me.

    Found a lot of nice solutions for false cielings but as we are already at minimal hieght we decided to work with what we had. The ceiling was filthy (as was the rest of the place, its disgusting what people will live with and in at times), so we hired a steam cleaner today and cleaned it up to stage were we think it will take paint (working above your head all day is hard work I have decided). Durobond in Sydney make a specialist paint to cover and seal vermiculite. Have that in hand and will spray in a couple of weeks when I get something else out of the way. If necesssary it can be topped with normal ceiling white. Will post again when its done (good or bad)

    Well, the job is done and looks good. Starting looking like a badly run fish and chip shop roof in the kitchen area but now looks great. For any other brave (foolish?) souls who try this, this is what we found works:

    – Clean roof in worst room with a steam cleaner (rented through a company called Steam Australia)
    – Apply Durobond in the steam cleaned area, went straight to ceiling white in other rooms that were in OK condition (note comment in the thread re Bondcrete may be an option). Finish coat in ceiling white (went on well after the Durobond)
    – Used roller with 25mm nap, this greatly improved application and coverage. Use of normal shorter nap rollers makes it very hard work. Looked at spraying, but too messy.
    – Used small sponges to get into corners and edges
    – People say this stuff takes lots of paint…this is true….a rough calculation indicates a paint budget of 1 litre per square metre is what you need

    Total cost has been about $800 plus our own labour (maybe 30 hours….made longer by the need to steam clean)

    With what we know now would we do it again? for one in good condition yes…..for one in poor condition I would investigate removal via an asbestos removal service….probably more expensive once off but then the beast is gone.